ADB Safegate IDM 8000 User Manual Download Page 65

Page: 65 / 118

5.3.2 AFL-Circuit Connection

•

Connect each circuit to pair of terminals marked with capital and small characters (e.g. A, a)

•

If more circuits than one is used the connectors are in alphabetical order i.e. circuit 1 = A, a, circuit 2 = B, b etc.

•

If grounding is used connect the cable shields to the grounding terminals on the cable fixing rail of the high voltage

compartment.

5.3.3 Serial Remote Control Connection

•

Connect the bus cable with D9 connector directly on the face of the serial control card.

Note

: Make sure that the connector is designed for that specific bustype (e.g. Profibus). For more information, see Appendix A –

Serial communication interface – Profibus DP connection. If the connectors have termination switches, make sure their settings

conform to bus configuration (normally first and last physical units are terminated. Remember that there are termination

switches on the serial control cards too!). It is recommended to use the termination in the cable connector to be able to replace

any unit without affecting the bus operation. Make sure that the node address setting conforms to the bus configuration.

5.3.4 Parallel Remote Control Connection

•

Connect the parallel control cable directly on the D37 connector located on the face of the card. For more information, see

Appendix E – Parallel control interface signal list.

•

Optionally IDM8000 can be delivered with terminal block-connections inside the low voltage compartment. The signal

connection details are equal to the D37 connector.

Note

: Before connecting, check that the remote control voltage setting conforms to the control voltage used.

5.4 Load matching

Load matching is provided from 45% to 100% with 5% and 10% taps on the Main Transformer. Benefits of load matching is

described in section 1.3.3 Main Transformer, Efficiency and Power Factor.

UM_IDM-8000, Rev. 1.7, 2021/05/06

Summary of Contents for IDM 8000







































































































Search results

Summary of Contents for IDM 8000

Reviews:

Brands by name

Popular brands

ADB Safegate IDM 8000, User Manual

Search results

Summary of Contents for IDM 8000

Reviews:

Brands by name

Popular brands