ADB Safegate IDM 8000 User Manual Download Page 51

Page: 51 / 118

Setting sequence

1. Go to lamp fault setting by selecting Set/Set/LF.

1. If necessary adjust level A and B with + / - , select Set and then select Next.

1. If the CCR is with direction changer, choose the other direction and adjust levels A and B as in step 2. The levels for both directions are

updated whenever direction is changed.

1. If necessary adjust delay time as in step 2.

Operational test

Adjust the alarm level below actual lamp fault level of the circuit or make more lamps faults than the alarm levels into the circuit and make

sure that alarms are generated in due time.

4.6.3 Earth Fault Setting

When the isolation resistance of the AFL-circuit decreases below the earth fault levels (A and B) corresponding fault indication

is generated. In case the earth fault maintenance switch function is enabled (i.e. selected on from the system settings) and the

maintenance switch is on level B causes tripping of the CCR and is therefore a protective function.

Header/function

Data 1

Data 2

Fact set

Allowed range

Earth fault set

Isolation level

Level A

0,1M ohm

0.01-2.50Mohm in 0.01Mohm steps

Isolation level

Level B

1M ohm

0.1-25Mohm in 0.1Mohm steps

Delay time

Delay

10s

1-99s in 1s steps

Setting sequence

1. Go to Earth fault setting by selecting Set / Set / EF.

1. If necessary adjust levels A and B with + / - , select Set and then select Next.

1. If necessary adjust delay time as in step 2.

Operational test

Adjust the alarm level higher than actual isolation level of the circuit or make an artificial earth fault in the circuit and make sure that alarms

are generated in due time.

Warning!

De-energize the CCR before making the earth fault.

UM_IDM-8000, Rev. 1.7, 2021/05/06

Summary of Contents for IDM 8000







































































































Search results

Summary of Contents for IDM 8000

Reviews:

Brands by name

Popular brands

ADB Safegate IDM 8000, User Manual

Search results

Summary of Contents for IDM 8000

Reviews:

Brands by name

Popular brands