ADB Safegate AXON FAA L-852A User Manual Download Page 74

Page: 74 / 98

C - Bottom Cover Assemblies

Quantity per

spare part code

fitting

spare part

EQ converter, style 6 cord set

SP.AS00021-R13

EQ converter, 3-pole cord set

SP.AS00021-R1F

EQ converter, style 1 SJO jacketed cord set

SP.AS00021-R1J

Cord sets, 8-inch and 12-inch

Quantity per

spare part code

fitting

spare part

Cord set, L-823 style 1, 8" bottom pan

1 or 2

SP.73A0193/1

Cord set, L-823 style 1, 12" bottom pan

1 or 2

SP.73A0194/1

Cord set, L-823 style 6, 8" & 12" bottom pan

1 or 2

SP.SGE96253351

Cord set, 3-pole, 8" & 12" bottom pan

1 or 2

SP.SGEFR500160

Cable retaining clamp, for use with style 1 cord set

1 or 2

SP.MB00003-013-01

Ground lug kit

SP.72A0401

Prism spare parts, 8-inch and 12-inch

Quantity per

spare part code

fitting

spare part

Prism kit, taxiway, standard

1 or 2

SP.4072.40.412

Prism kit, taxiway reinforced

1 or 2

SP.4072.42.090

Screws and gaskets, 8-inch

Quantity per

spare part code

fitting

spare part

Pressure release screw with o-ring

SP.MF00090-000-01

Gasket, 8" Bottom pan

SP.MS00005-000-01

Screws, 8" Bottom pan

100

SP.MFPM5PT-714-01

Screws, light engine assembly mounting

100

SP.MFPM4PT-710-01

Wire harness, 8-inch and 12-inch

Quantity per

spare part code

fitting

spare part

Wire harness, power supply to light engine

1 or 2

SP.EW00070-150-01

Wire harness, power supply to heater

1 or 2

SP.EW00069-150-01

Fuse

Quantity per

spare part code

fitting

spare part

Fuse Resistors (only for fixtures with monitoring (M))

1 or 2

6132.00.250

Note

All screws for fastening are included.
Component availability or design may be subject to change due to unforeseen circumstances. This document is

subject to change or new information from ADB SAFEGATE, as and when available or if required, with reservation for

error or price changes.
For more information or assistance with ordering spare parts, contact ADB SAFEGATE, see

www.adbsafegate.com

AXON Taxiway Inset Lights, 8-inch and 12-inch
Spare Parts

64
Copyright

Summary of Contents for AXON FAA L-852A

























































































Search results

Summary of Contents for AXON FAA L-852A

Reviews:

Related manuals for AXON FAA L-852A

Brands by name

Popular brands

ADB Safegate AXON FAA L-852A, User Manual

Search results

Summary of Contents for AXON FAA L-852A

Reviews:

Related manuals for AXON FAA L-852A

Brands by name

Popular brands