ADB Safegate AXON FAA L-852A User Manual Download Page 41

Page: 41 / 98

5.3.3 Replacing the Power Wire Harness

Figure 11: Power harness replacement

NOTICE

The arctic kit wire harness is soldered to the light engine. The arctic kit is to be replaced if this harness is damaged.

Tools to be used:

•

Variable-speed/Torque drill driver with T20 bit

NOTICE

Do not use an Impact driver.

1. Open the light.

Note

Refer to the

Opening a Light Fixture — disconnecting the Bottom Pan from the Top Cover

section.

2. Remove the LED brackets (3 pieces M5 screws per bracket) to access the connector of the LED wire.

Make sure you dispose the old screws and use new screws.

Figure 12: LED bracket removal

3. Disconnect the old wire harnesses.

Make sure you dispose the old wire harnesses and use new wire harnesses.

4. Connect the new wire harnesses.

UM-5056, Rev. 1.0.17, 2022/12/08

Summary of Contents for AXON FAA L-852A

























































































Search results

Summary of Contents for AXON FAA L-852A

Reviews:

Related manuals for AXON FAA L-852A

Brands by name

Popular brands

ADB Safegate AXON FAA L-852A, User Manual

Search results

Summary of Contents for AXON FAA L-852A

Reviews:

Related manuals for AXON FAA L-852A

Brands by name

Popular brands