ADB Safegate AXON FAA L-852A User Manual Download Page 12 | Manualshive

Page: 12 / 98

background image

1.1.1 Introduction to Safety

CAUTION

Unsafe Equipment Use

This equipment may contain electrostatic devices, hazardous voltages and sharp edges on components

• Read installation instructions in their entirety before starting installation.
• Become familiar with the general safety instructions in this section of the manual before installing,

operating, maintaining or repairing this equipment.

• Read and carefully follow the instructions throughout this manual for performing specific tasks and

working with specific equipment.

• Make this manual available to personnel installing, operating, maintaining or repairing this

equipment.

• Follow all applicable safety procedures required by your company, industry standards and

government or other regulatory agencies.

• Install all electrical connections to local code.
• Use only electrical wire of sufficient gauge and insulation to handle the rated current demand. All

wiring must meet local codes.

• Route electrical wiring along a protected path. Make sure they will not be damaged by moving

equipment.

• Protect components from damage, wear, and harsh environment conditions.
• Allow ample room for maintenance, panel accessibility, and cover removal.
• Protect equipment with safety devices as specified by applicable safety regulations
• If safety devices must be removed for installation, install them immediately after the work is

completed and check them for proper functioning prior to returning power to the circuit.

Failure to follow this instruction can result in serious injury or equipment damage

Additional Reference Materials

Important Information

•

IEC - International Standards and Conformity Assessment for all electrical, electronic and related technologies.

•

IEC 60364 - Electrical Installations in Buildings.

•

FAA Advisory: AC 150/5340-26 (current edition), Maintenance of Airport Visual Aid Facilities.

•

Maintenance personnel must refer to the maintenance procedure described in the ICAO Airport Services Manual,

Part 9.

•

ANSI/NFPA 79, Electrical Standards for Metalworking Machine Tools.

•

National and local electrical codes and standards.

1.1.2 Intended Use

CAUTION

Use this equipment as intended by the manufacturer

This equipment is designed to perform a specific function, do not use this equipment for other purposes

• Using this equipment in ways other than described in this manual may result in personal injury, death

or property and equipment damage. Use this equipment only as described in this manual.

Failure to follow this instruction can result in serious injury or equipment damage

AXON Taxiway Inset Lights, 8-inch and 12-inch
Safety

2
Copyright

©

ADB Safegate, All Rights Reserved

«
...
10
11
12
13
14
...
»

Summary of Contents for AXON FAA L-852A



































































































Reviews:

No comments

Related manuals for AXON FAA L-852A

Brand: Fein Pages: 248

Brand: ZF Pages: 30

Brand: Raymarine Pages: 111

Brand: Modulate Pages: 2

Brand: XAG Pages: 24

Brand: FEAS Pages: 72

Brand: Handler Pages: 25

Varycolor MICRO 150HTI

Brand: JB-Lighting Pages: 18

Brand: OHAUS Pages: 84

Brand: ParaBody Pages: 6

Brand: ParaBody Pages: 11

Brand: A&D Pages: 29

Brand: Zodiac Pages: 2

Brand: Zipper Mowers Pages: 37

Brand: Zimmer Pages: 46

Brand: Garmin Pages: 2

Brand: Parker Pages: 58

ZA top SM315.100A

Brand: ZIEHL-ABEGG Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands