ADB Safegate AXON FAA L-852A User Manual Download Page 40

Page: 40 / 98

5.3.2 Closing a Light Fixture — connecting the Bottom Pan to the Top Cover

Note

Replacement light engines are provided with the power wire harness installed.

Tools to be used:

•

Variable-speed/Torque drill driver with T25 bit

NOTICE

Do not use an Impact driver.

•

Flat-head screwdriver

1. Clean all the contact surfaces of the light fixture and of the housing carefully.
2. Press the gasket (located between top cover and inner pan) into the O-ring Groove.

Make sure the gasket placed correctly.

Important

The O-ring Gasket must always be changed when the fixture is being disassembled.

3. Connect the wires:

a. Press carefully to connect the wires lead in from the light engine on the converter.

b. Press carefully to connect the wires lead in from the light engine on the converter, if the heater kit is in place.

4. Put the Top Cover onto the Bottom Pan.

Make sure the poke-yoke (alignment pin) is in the placed correctly.

Important

Do not pinch the wires or the gasket.

5. Put the light fixture on a surface with the top cover facing down.
6. Torque:

a. Use new fixation screws to torque in star pattern at 31 in-lbs (3.5 Nm).

b. Retorque the screws in star pattern at 31 in-lbs (3.5 Nm).

7. Follow the water-tightness test procedure.

Note

Refer to the

Checking the Light Fixture for Water-tightness

section.

AXON Taxiway Inset Lights, 8-inch and 12-inch
Maintenance

30
Copyright

Summary of Contents for AXON FAA L-852A

























































































Search results

Summary of Contents for AXON FAA L-852A

Reviews:

Related manuals for AXON FAA L-852A

Brands by name

Popular brands

ADB Safegate AXON FAA L-852A, User Manual

Search results

Summary of Contents for AXON FAA L-852A

Reviews:

Related manuals for AXON FAA L-852A

Brands by name

Popular brands