ADB Safegate AXON FAA L-852A User Manual Download Page 26

Page: 26 / 98

4.3.1 Installation Overview

On a shallow base.
The 8” dia. base is secured in the pavement by means of resin. Correct positioning and leveling are obtained with a jig with

sighting telescope. Wires between the light and the series transformer are installed either in saw cuts in the pavement filled

with resin or in pipes in the lower concrete layers. Mounting on existing or new, larger diameter bases, is made possible by

means of dedicated adapter rings.

Figure 4: Installation on 8” shallow base

On a FAA L-868B size B steel base.
The 8” dia. light is mounted in an 8” to 12” dia. snow plow or adapter ring bolted onto the base. The 12” fixture is directly

mounted without a separate ring. The bases are interconnected by means of conduits protecting the cables. See FAA AC

150/5340-30 for additional design guidance on deep base cans. The series transformer is installed under the light or in a

separate pit. See data sheet A.05.120 or DS2012 for more information on base cans.

4.3.2 INTEROPERABILITY

Top cover versions

Note

Please check interoperability matrix for information on torque values and compatibility towards different bases.

AXON Taxiway Inset Lights, 8-inch and 12-inch
Installation

16
Copyright

Summary of Contents for AXON FAA L-852A

























































































Search results

Summary of Contents for AXON FAA L-852A

Reviews:

Related manuals for AXON FAA L-852A

Brands by name

Popular brands

ADB Safegate AXON FAA L-852A, User Manual

Search results

Summary of Contents for AXON FAA L-852A

Reviews:

Related manuals for AXON FAA L-852A

Brands by name

Popular brands