ADB Safegate AXON FAA L-852A User Manual Download Page 48

Page: 48 / 98

6. Mount the new cable gland gaskets.
7. Replacement:

a. Pull the secondary wires through the Strain-relief Plate and the cable gland gaskets and

b. Mount the new secondary cable by torquing the new Strain-relief Bolt at.XX in-lbs (XX Nm).

8. Locking:

a. Lock the secondary cables leading to the converter by opening the cable holes prying a thin screwdriver on the cable

release opening and mounting the wires in place and

b. Lock the cables by releasing screwdriver from the opening.

9. Close the light.

Note

Refer to the

Closing a Light Fixture — connecting the Bottom Pan to the Top Cover

section.

5.3.10 Resetting the Fail-open Converter

Parts

•

Fuse resistor spare part kit: 20210209 (20 pcs)

Info

•

Converter with 1 connector have 2 fuse resistors

•

Converter with 2 connectors have 4 fuse resistors

Reset / replace the fuse resistors

1. Disconnect and disassemble the light fixture.
2. Locate the fuse resistors.

Note

Refer to

Figure 18

and

Figure 19

figures.

Refer to Figure.

Figure 18: Converter, 1-connector

AXON Taxiway Inset Lights, 8-inch and 12-inch
Maintenance

38
Copyright

Summary of Contents for AXON FAA L-852A

























































































Search results

Summary of Contents for AXON FAA L-852A

Reviews:

Related manuals for AXON FAA L-852A

Brands by name

Popular brands

ADB Safegate AXON FAA L-852A, User Manual

Search results

Summary of Contents for AXON FAA L-852A

Reviews:

Related manuals for AXON FAA L-852A

Brands by name

Popular brands