manualshive.com logo in svg

ADB Safegate AXON FAA L-852A, User Manual

Share
Download
ADB Safegate AXON FAA L-852A User Manual Download Page 39

5.3 Workshop Maintenance

The workshop maintenance refers to following:

1. Open a Light Fixture
2. Close a Light Fixture
3. Replace the Power Wire Harness
4. Replace the Light Engine Assembly
5. Replace the Prism
6. Replace the Top Cover Assembly
7. Replace the Bottom Pan Assembly
8. Replace the secondary Cable
9. Reset the Fail-open Converter

10. Check the Light Fixture for Water-tightness

5.3.1 Opening a Light Fixture — disconnecting the Bottom Pan from the Top Cover

Tools to be used:

•

Variable-speed/Torque drill driver with T25 bit

NOTICE

Do not use an Impact driver.

•

Flat-head screwdriver

1. Place the light fixture upside down.
2. Loosen the Pressure Release Screw.
3. Unscrew the fixation screws.

Make sure you dispose the old screws and use new screws.

4. Lift the Bottom Pan without damaging the connecting wires.

CAUTION

Make sure you do not damage the cables when opening the light fixture.

5. Disconnect the wires:

a. Pull carefully to disconnect the wires between the converter and the light engine.

b. Pull carefully to disconnect the wires between the converter and the heater kit(s), if the heater kit is in place.

6. Remove the gasket between the Top Cover Assembly and the Inner Pan Assembly.

Make sure you dispose the old gasket and use a new gasket.

UM-5056, Rev. 1.0.17, 2022/12/08

29

Copyright 

©

 ADB Safegate, All Rights Reserved

Summary of Contents for AXON FAA L-852A



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands