ACS contsys DAL-311x0x0S Operating Instructions Manual Download Page 1 | Manualshive

Page: 1 / 40

background image

Technical features:

• red display of -19999…99999 digits (optional: green, orange or blue)
• installation depth: 120 mm without plug-in terminal
• min/max memory
• 30 parameter driven supporting points
• display flashing at threshold value exceedance / undercut
•

[O]

-key (zero key) for triggering of Hold, Tara

• permanent min/max-value recording
• volume measurement (totaliser)
• mathematical functions like e.g. reciprocal value, square root, squaring or rounding
• setpoint generator
• sliding averaging
• brightness control
• programming interlock via access code
• protection class IP65 at the front
• plug-in screw terminal
• option: sensor supply
• option: galvanic isolated digital input
• option: 1 or 2 analog outputs
• option: 2 or 4 relay outputs or 8 PhotoMos outputs
• option: interface RS232 or RS485
• accessories: PC-based configuration kit PM-TOOL incl. CD and USB-adapter for devices

without keypad and for a simple adjustment of standard devices

User manual M3

Direct current / direct voltage signals: 0/4-20 mA, 0-10 VDC

96x48

M3_11GB.pdf update: 10.04.2015

Technical features:

• red display of -19999…99999 digits (optional: green, orange or blue)
• installation depth: 120 mm without plug-in terminal
• min/max memory
• 30 parameter driven supporting points
• display flashing at threshold value exceedance / undercut
•

[O]

-key (zero key) for triggering of Hold, Tara

• permanent min/max-value recording
• volume measurement (totaliser)
• mathematical functions like e.g. reciprocal value, square root, squaring or rounding
• setpoint generator
• sliding averaging
• brightness control
• programming interlock via access code
• protection class IP65 at the front
• plug-in screw terminal
• option: sensor supply
• option: galvanic isolated digital input
• option: 1 or 2 analog outputs
• option: 2 or 4 relay outputs or 8 PhotoMos outputs
• option: interface RS232 or RS485
• accessories: PC-based configuration kit PM-TOOL incl. CD and USB-adapter for devices

without keypad and for a simple adjustment of standard devices

User manual M3

Direct current / direct voltage signals: 0/4-20 mA, 0-10 VDC

96x48

M3_11GB.pdf update: 10.04.2015

Operating Instructions

DAL-311x0x0S

Direct current / direct voltage signals: 0/4-20 mA, 0-10 VDC

1
2
3
...
»

Summary of Contents for DAL-311x0x0S









































Reviews:

No comments

Related manuals for DAL-311x0x0S

Brand: Omega Engineering Pages: 22

Brand: Energic Plus Pages: 12

Solicap M FTI55

Brand: Endress+Hauser Pages: 92

LaserHybrid SB 360i

Brand: Fronius Pages: 104

Brand: PCE Health and Fitness Pages: 11

MultiScanner HD800 OneStep

Brand: Zircon Pages: 2

Brand: HERON Pages: 2

Brand: CryptOn Pages: 13

Brand: Westfalia Pages: 18

Brand: Hanna Instruments Pages: 28

Brand: UEi Pages: 16

NADAL Borreliosis Ag Test

Brand: nal von minden Pages: 28

Brand: Triplett Pages: 34

ProScale 950 Series

Brand: Accurate Technology Pages: 16

Brand: Omega Pages: 14

wtw Cleaning Air Box -115 VAC

Brand: Xylem Pages: 32

Brand: Powerfix Profi Pages: 93

Module NI PXI-8250

Brand: National Instruments Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands