ACS contsys DAL-311x0x0S Operating Instructions Manual Download Page 21

Page: 21 / 40

ACS-CONTROL-SYSTEM GmbH

l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]

5. Setting up the device

Menu level

Parameterisation level

User code

U.Code:

Default:

0000

Via this code reduced sets of parameters can be set free. A change of the

U.CodE

can be done

via the correct input of the

A.CodE

(master code).

Master code,

A.Code

Default:

1234

By entering

A.CodE

the device will be unlocked and all parameters are released.

Release/lock analog output parameters,

Out.LE:

Default:

all

Analog output parameters can be locked or released for the user:
-

En-oF:

the initial or final value can be changed in operation mode

Out.EO:

the output signal can be changed from e.g. 0-20 mA to 4-20 mA or 0-10 VDC

ALL:

analog output parameters are released

no:

all analog output parameters are locked

Release/lock alarm parameters,

AL.LEU:

Default:

all

This parameter describes the user release/user lock of the alarm:

- LIMIt

: here only the range of value of the threshold values 1-4 can be changed

ALrM.L

: here the range of value and the alarm trigger can be changed

ALL:

all alarm parameters are released

no:

all alarm parameters are locked

Back to menu group level,

rEt

With

[P]

the selection is confirmed and the device changes into menu group level

„–COD–“

Menu group level

5.4.3. Safety parameters

Menu level

Summary of Contents for DAL-311x0x0S









































Search results

Summary of Contents for DAL-311x0x0S

Reviews:

Related manuals for DAL-311x0x0S

Brands by name

Popular brands

ACS contsys DAL-311x0x0S, Operating Instructions Manual

Search results

Summary of Contents for DAL-311x0x0S

Reviews:

Related manuals for DAL-311x0x0S

Brands by name

Popular brands