ACS contsys DAL-311x0x0S Operating Instructions Manual Download Page 9 | Manualshive

Page: 9 / 40

background image

ACS-CONTROL-SYSTEM GmbH

l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]

9

7

4. Description of function and operation

Function chart

:

4.1 Parameterisation software PM-TOOL:

Part of the PM-TOOL are the software on CD and an USB-cable with device adapter. The connection

happens via a 4-pole micromatch-plug on the back side of the device, to the PC-side the connection

happens via an USB plug.

System requirements: PC incl. USB interface

Software: Windows XP, Windows VISTA

With this tool the device configuration can be generated, omitted and saved on the PC. The parameters can

be changed via the easy to handle program surface, whereat the operating mode and the possible selection

options can be preset by the program.

CAUTION!

During parameterisation with connected measuring signal, make sure that the measuring signal has no

mass supply to the programming plug. The programming adapter is galvanic not isolated and directly

connected with the PC. Via polarity of the input signal, a current can discharge via the adapter and destroy

the device as well as other connected components!

«
...
7
8
9
10
11
...
»

Summary of Contents for DAL-311x0x0S









































Reviews:

No comments

Related manuals for DAL-311x0x0S

Endura AZ20 series

Brand: ABB Pages: 8

Brand: Kane Pages: 20

Brand: XS Scuba Pages: 24

Brand: Gardner Bender Pages: 7

Brand: J.P. Instruments Pages: 9

Brand: J.ASSY Pages: 13

NANOCOLOR UV/VIS II

Brand: Macherey-Nagel Pages: 99

CP-4900 Micro-GC

Brand: Varian Pages: 13

Brand: Wagner Meters Pages: 17

Brand: Yamaha Pages: 48

Clavinova CVP-601

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 28

Brand: Unitech Pages: 18

Vortex Flow Industry

Brand: Grundfos Pages: 16

Brand: Spacelabs Pages: 156

Brand: AccuMac Pages: 10

Brand: Kobold Pages: 55

Brand: Victron energy Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands