Acer AR360 F1 Series User Manual Download Page 52

Page: 52 / 188

3 System upgrades

Removing and installing a 2.5” hard disk
drive

Removing a 2.5” hard disk drive with carrier

Observe the ESD precautions described on page 27.

Remove the carrier with failed HDD.

Remove the HDD carrier.

(1) Unlock the HDD carrier latch.
(2) Slide the HDD carrier latch to release the lever.

(3) Pull the lever up.

(4) Grasp the lever and pull the carrier from the chassis.

Observe the post-installation instructions described on page 28.

Installing a 2.5” hard disk drive with carrier

Slide the HDD carrier all the way into the drive bay.

Use the lever to push the HDD carrier into the chassis until it locks
in place, then close the HDD carrier lever.

Summary of Contents for AR360 F1 Series




























































































































































































Search results

Summary of Contents for AR360 F1 Series

Reviews:

Related manuals for AR360 F1 Series

Brands by name

Popular brands

Acer AR360 F1 Series, User Manual

Search results

Summary of Contents for AR360 F1 Series

Reviews:

Related manuals for AR360 F1 Series

Brands by name

Popular brands