Acer AR360 F1 Series User Manual Download Page 76

Page: 76 / 188

3 System upgrades

Removing a memory module:

Important: Before removing any DIMM from the mainboard,
make sure to create a backup file of all important data.

Remove the memory module.

Press the holding clips on both sides of the DIMM slot outward to
release the DIMM (1).

Gently pull the DIMM upward to remove it from the DIMM slot (2).

If you intend to install a new memory module, refer to the
previous section.

To reconfigure the system memory:

The system automatically detects the amount of memory installed. Run
the BIOS setup to view the new value for total system memory and
make a note of it.

Summary of Contents for AR360 F1 Series




























































































































































































Search results

Summary of Contents for AR360 F1 Series

Reviews:

Related manuals for AR360 F1 Series

Brands by name

Popular brands

Acer AR360 F1 Series, User Manual

Search results

Summary of Contents for AR360 F1 Series

Reviews:

Related manuals for AR360 F1 Series

Brands by name

Popular brands