Acer AR360 F1 Series User Manual Download Page 159

Page: 159 / 188

143

Note: KVM Remote Console Redirection needs to run in a JAVA
environment. Ensure the JAVA Runtime Environment Tool is
installed.

Accessing Acer Smart Console

Open your web browser and enter the system’s IP address. You will
be prompted to enter a username and password.

Enter the root username and password in the login screen.

•

Username: root

•

Password: superuser

Click Login. The Acer Smart Console page appears.

Note: The default username is root and the default password is
superuser. Both the username and password are case sensitive and
should be entered in lower case each time.

Important: Logging into the console allows you full administrative
rights. Once logged in, you should you change your password.

Summary of Contents for AR360 F1 Series




























































































































































































Search results

Summary of Contents for AR360 F1 Series

Reviews:

Related manuals for AR360 F1 Series

Brands by name

Popular brands

Acer AR360 F1 Series, User Manual

Search results

Summary of Contents for AR360 F1 Series

Reviews:

Related manuals for AR360 F1 Series

Brands by name

Popular brands