Acer AR360 F1 Series User Manual Download Page 161 | Manualshive

Page: 161 / 188

background image

145

Server Health

Displays data related to the server's health, such as sensor readings and
the event log. This menu has two options: Sensor Readings and Event
Log.

Sensor Readings

Allows you to monitor status of the voltages of the power supply, the
fan speed, processor and system temperature sensors.

Sensor Display Color

Indicates the health of the system processor, fan, temperature and
voltage in a box displayed before each sensor category.
•

Green: Indicates the system is in good health and no alerts were
detected on the sensors.

•

Amber: Indicates at least one sensor has a warning alert.

•

Red: Indicates at least on sensor has a critical alert.

Threshold

Click Show Thresholds to view the threshold parameters of each
sensor. It displays the Low Non-Critical (NC), High Non-Critical (NC),
High Critical Threshold (CT) threshold information, and these items can
not be modified. When each threshold matches alert level, system will
send the alert to the specified destinations. To configure the specified

«
...
159
160
161
162
163
...
»

Summary of Contents for AR360 F1 Series





























































































































































































Reviews:

No comments

Related manuals for AR360 F1 Series

ColorPASS-Z5000

Brand: Canon Pages: 130

Brand: Acano Pages: 17

Brand: Premio Pages: 3

Brand: TRENDnet Pages: 14

Eserver xSeries 360 Type 8686

Brand: IBM Pages: 74

Brand: B&B Pages: 55

Brand: Eaton Pages: 2

Brand: Kontron Pages: 90

Past Ethernet Combo Print Server PS-1216U

Brand: Edimax Pages: 23

Brand: disguise Pages: 12

Access Server 316

Brand: Cabletron Systems Pages: 70

Brand: Advantech Pages: 38

Brand: Blonder tongue Pages: 20

SUPERSERVER 6026TT-IBQF

Brand: Supermicro Pages: 100

SuperServer 510P-WT

Brand: Supermicro Pages: 113

SuperWorkstation 7049GP-TRT

Brand: Supermicro Pages: 133

Brand: Neat Pages: 124

Brand: Intel Pages: 167

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands