Acer AR360 F1 Series User Manual Download Page 173 | Manualshive

Page: 173 / 188

background image

157

interfaces. Operator privilege can not disable individual channels
or change user access privileges.

•

Administrator: The administrator privilege has full access and can
configure the software and add users. Administrator privilege
have access to all BMC commands, including configuration
commands for disabling a communication channel.

Modifying a user account

1

On the Users page click Modify User.

2

Enter the username.

3

Enter the password.

4

Re-enter the password.

5

Select a privilege level from the drop-down menu.

6

Click Modify.

Remote Control

The Remote Control menu allows you to start a Remote Console
session with the host system and manage power remotely. This menu
include two options: KVM Remote Console Redirection and Server
Power Control.

«
...
171
172
173
174
175
...
»

Summary of Contents for AR360 F1 Series





























































































































































































Reviews:

No comments

Related manuals for AR360 F1 Series

Brand: NTI Pages: 35

Brand: EMC Pages: 34

Brand: Autonomic Pages: 17

Brand: FS Pages: 91

Brand: Stratus Pages: 106

Brand: Panasonic Pages: 17

Brand: Panasonic Pages: 42

Brand: Panasonic Pages: 316

Brand: Panasonic Pages: 456

IC125-FASTPOCKET-FX

Brand: SEH Pages: 20

Brand: SEH Pages: 32

Brand: Biamp Pages: 11

TalkAnytime TA2410

Brand: Multitech Pages: 235

Brand: Corvus systems Pages: 108

Brand: Silicon Graphics Pages: 62

Brand: Silicon Graphics Pages: 70

Brand: Sugon Pages: 155

IXG CloudBridge

Brand: evertz Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands