Acer AR360 F1 Series User Manual Download Page 136 | Manualshive

Page: 136 / 188

background image

5 System troubleshooting

120

Verifying the condition of the storage devices

As POST determines the system configuration, it tests for the presence
of each mass storage device installed in the system. As each device is
checked, its activity indicator should turn on green briefly. Check the
activity indicators for the hard drive(s), DVD-ROM drive, and any other
device you may have installed.

If any of these indicators fail to light up, refer to related problems
listed in the “HDD activity indicator does not light.” on page 121.

Confirming loading of the operating system

Once the system boots up, the operating system prompt appears on
the screen. The prompt varies according to the operating system. If the
operating system prompt does not appear, see "No Characters Appear
on Screen" on page 94.

«
...
134
135
136
137
138
...
»

Summary of Contents for AR360 F1 Series





























































































































































































Reviews:

No comments

Related manuals for AR360 F1 Series

Brand: Oki Pages: 121

QS21 - BladeCenter - 0792

Brand: IBM Pages: 110

Express5800/320Fa-L

Brand: NEC Pages: 406

Brand: ANTAIRA Pages: 2

SUPERSERVER 6015C-NT

Brand: Supermicro Pages: 110

PRIMERGY BX620 S5

Brand: Fujitsu Pages: 50

PRIMERGY BX620 S4

Brand: Fujitsu Pages: 81

PRIMERGY BX900 S1

Brand: Fujitsu Pages: 46

PRIMERGY BX620 S6

Brand: Fujitsu Pages: 56

Primergy BX920 S4

Brand: Fujitsu Pages: 66

PRIMERGY BX920 S2

Brand: Fujitsu Pages: 70

PRIMERGY BX920 S2

Brand: Fujitsu Pages: 102

PRIMERGY BX400 S1

Brand: Fujitsu Pages: 60

PRIMERGY BX900 S1

Brand: Fujitsu Pages: 144

Primergy BX900 S2

Brand: Fujitsu Pages: 108

PRIMERGY BX600 PG-LNB101

Brand: Fujitsu Pages: 28

PRIMERGY BX600 S3

Brand: Fujitsu Pages: 103

PRIMERGY BX620 S5

Brand: Fujitsu Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands