background image

Changes may be made periodically to the information in this publication without obligation 
to notify any person of such revision or changes.  Such changes will be incorporated in new 
editions of this manual or supplementary documents and publications.  This company makes 
no representations or warranties, either expressed or implied, with respect to the contents 
hereof and specifically disclaims the implied warranties of merchantability or fitness for a 
particular purpose.

Record the model number, serial number, purchase date, and place of purchase information in 
the space provided below.  The serial number and model number are recorded on the label 
affixed to your server.  All correspondense concerning your unit should include the serial 
number, model number, and purchase information.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in 
any form or by any means, electronic, mechanical, photocopy, recording, or otherwise, 
without the prior written permission of Acer Incorporated.

Model Number : _________________________________

Serial Number: ___________________________________

Purchase Date: ___________________________________

Place of Purchase: ________________________________

Copyright © 2002 Acer Incorporated
All Rights Reserved.  

Acer Altos G900 
User’s guide

 

Acer and the Acer logo are registered trademarks of Acer Inc.  Other company’s product 
names or trademarks are used herein for identification purposes only and belong to their 
respective companies.

AA G900 ug - EN.book Page ii Wednesday, September 25, 2002 5:23 PM

 

Summary of Contents for Altos G900

























































































































































































































































Reviews: