manualshive.com logo in svg

ABB Zenith ZBTS T Series, Installation And Operating Instruction, Page: 99 / 112

Share
Download
ABB Zenith ZBTS T Series Installation And Operating Instruction Download Page 99

2

99

3 4ZBT S _ 3 0 -1 2 0 0A  rev. A  /  1 S CC 3 0 3 0 4 3 M 0 2 01

3

9.7.3.1  Other Features of TPME_
•  Meets and/or exceeds the requirements 

of UL 1449 3rd Edition, cUL, NEMA LS-1 
and NEC Article 285

•  Thermally protected MOVs eliminate the 

need for additional upstream overcur-
rent protection

•  Factory wired, no field connections (ex-

cept remote alarm contacts)

All specified  documents of Integrated 
SPD are delivered with the cabinet. See 
drawing 71R-2097.

— 
Table 9.10  Technical Data, Integrated SPD for ATS,  
type TPME_

— 
Fig. 9.19  Integrated SPD, type TPME_

9.7.3  Integrated SPD, Type TPME_

Surge Protective Devices (SPD) have be-
come a standard component in today’s 
data centers, office buildings and manu-
facturing facilities because they improve 
equipment uptime and reduce expensive 
facility equipment repairs. SPD have al-
ways been regarded as best in class. 

This important component is available as 
accessory factory-mounted inside Zenith 
Bypass-Isolation automatic transfer 
switch for optimal facility equipment 
protection.

Integral SPD is factory wired to the load-
side of the ATS to minimize lead lengths 
and provide the highest possible surge 
protection for the connected critical 
loads. The integral mounting conserves 
wall space and reduces installation costs.

Technical Specifications
Operating 
Frequency: 

50/60 Hz

Connection: 

#10 Conductors, Parallel 
Connected (40-600 Amp ATS)

#6 Conductors, Parallel 
Connnected (800-4000 Amp 

ATS)

Operating 
Temperature: 

-4°F to 104°F (-20°C to 40°C)

Operating 
Humidity: 

0% to 95% Non-Condensing

Weight: 

ME: 13 lbs. (5.9 kg) 

Summary of Contents for Zenith ZBTS T Series

















































































































Reviews:

No comments