manualshive.com logo in svg

ABB Zenith ZBTS T Series, Installation And Operating Instruction, Page: 70 / 112

Share
Download
ABB Zenith ZBTS T Series Installation And Operating Instruction Download Page 70

2

70

Zenith ZBTS T-series 100-1200A, I N S TA LL ATI O N  A N D  O PER ATI N G  I N S TR U C TI O N

—

7.  Installation

This equipment must only be installed by qualified electrical 
personnel. Disconnect all sources of electrical supply before 
performing installation. Consider all sources of power, 
including the possibility of backfeeding.

—

 

7.1  Final System Inspection

Prior to energizing the automatic transfer 
switch:

1 

Use a vacuum cleaner to remove all 
debris caused by transport or 
installation. 
 

2 

Verify that all cabled connections are 
correct and that phase rotation of 
both sources match.

3 

Check engine start connections.

4 

Verify the correct connections of all 
control wires.

5 

Adjust any optional accessories as 
required.

6 

Check the lug torque values of the 

power connections, see the lug 
torque values in table 7.1.

7 

Make sure that all covers and barriers 
are installed and properly fastened.

Each ABB Zenith Bypass-isolation auto-
matic transfer switch is factory wired and 
tested. A complete information package 
is furnished with each switch which 
includes:
•  Sequence of operation.
•  Description and operation of all acces-

sories supplied.

•  Control panel connection diagram and 

schematic.

•  Description and identification of all cus-

tomer field connections.

Installation of ABB Zenith Bypass-isola-
tion automatic transfer switch includes:
•  Mounting the Bypass-isolation transfer 

switch cabinet/enclosure.

 

Warning

 

Do not use a blower since debris may become 

lodged in electrical and mechanical compo-

nents and may cause damage and malfunction 

of the switch.

Summary of Contents for Zenith ZBTS T Series

















































































































Reviews:

No comments