manualshive.com logo in svg

ABB Zenith ZBTS T Series, Installation And Operating Instruction, Page: 11 / 112

Share
Download
ABB Zenith ZBTS T Series Installation And Operating Instruction Download Page 11

11

3 4ZBT S _ 3 0 -1 2 0 0A  rev. A  /  1 S CC 3 0 3 0 4 3 M 0 2 01

1

—

1.  Introduction

Operating instruction part of the manual 
(Chapters 1...6)  describes the basic oper-
ation of the Bypass-isolation automatic 
transfer switches Zenith ZBTS T-series 
100-1200A, manufactured by ABB. 

Mounting instructions for the Bypass-iso-
lation automatic transfer switches and for 
the available accessories, see Part 2, 
Chapters 7 and 8.

The regular maintenance instructions and 
useful tricks for service operations are 
descriped in Part 3, Chapter 9.

Dimension drawings, see Part 4,   
Chapter 10.

—

1.1  Hazard Categories

The following important highlighted in-
formation appears throughout this docu-
ment to warn of potential hazards or to 
call attention to information that clarifies 
a procedure.

Carefully read all instructions and become 
familiar with the devices before trying to 
install, operate, service or maintain this 
equipment.

 

Danger

  

Indicates a hazardous situation that, if not 

avoided, will result in death or serious injury 

or equipment damage.

 

Warning

 

Indicates a hazardous situation that, if not 

avoided, could result in death or serious injury 

or equipment damage.

 

Caution

 

Indicates a hazardous situation that, if not 

avoided, could result in minor or moderate in-

jury. Failure to comply with these instructions 

may result in product damage.

 

Notice

 

It is used to notify of practices not related to 

personal injury. Failure to comply with these 

instructions may result in product damage.

The safe operation of your Bypass-Isola-
tion Automatic Transfer Switch is ABB’s 
focus. The proper storage, installation, 
operation and maintenance will help in-
crease the life of Bypass-Isolation Auto-
matic Transfer Switch.

Summary of Contents for Zenith ZBTS T Series

















































































































Reviews:

No comments