manualshive.com logo in svg

ABB Zenith ZBTS T Series, Installation And Operating Instruction, Page: 77 / 112

Share
Download
ABB Zenith ZBTS T Series Installation And Operating Instruction Download Page 77

2

77

3 4ZBT S _ 3 0 -1 2 0 0A  rev. A  /  1 S CC 3 0 3 0 4 3 M 0 2 01

7.2.7  Engine/Generator Start Control 
Connections
The generator start and stop signals are 
wired at the factory from the switches to 
the Control Plate terminal block XGEN (in 
the lowest module of cabinet), see picture 
below.
•  Common, voltage supply –> From ATS 

(1) to XGEN: 1 and from Bypass (1) to 
XGEN: 2, these are factory-connected –> 
Customer connection 

XGEN: 1

•  Closes to start / NO –> From ATS (2) to 

XGEN: 3 and from Bypass (2) to XGEN: 4, 
these are factory-connected –> Cus-
tomer connection 

XGEN: 3

•  Opens to start / NC –> From ATS (3) to 

XGEN: 5 and from Bypass (3) to XGEN: 6, 
these are factory-connected –> Cus-
tomer connection 

XGEN: 5

Cable size: 0.5…10 mm

2

, 22-8 AWG

Stripping length: 12 mm, 0,47 in
Tightening torgue: 0.8...1 Nm, 7.1...8.9 lb.in

— 

Fig. 7.11  Adapter bay is an accessory for power  
connections from bottom

1

3

5

1 2

XGEN

X500

1  COMMON

3  CLOSES TO START

5  OPENS TO START

1  +24V

2  GND

External supply

(24V/0.5A) for Ekip

modules.

G

~

— 

Fig. 7.12  Generator start and stop signals are installed 
at the factory to the terminal block XGEN. The terminal 
block XGEN is ready for customer connections

Bypass

XGEN

1    2    3    4    5    6

Customer connections

ATS

1
2
3

1
2
3

AT

S: 1

AT

S: 2

BYP

ASS: 3

AT

S: 3

BYP

ASS: 2

BYP

ASS: 1

XGEN: 2
XGEN: 4
XGEN: 6

XGEN: 1
XGEN: 3
XGEN: 5

1

2

3

G

~

1 COMMON

2 CLOSES TO START

3 OPENS TO START

1

2

3

G

~

1 COMMON

2 CLOSES TO START

3 OPENS TO START

1

3

5

1 2

XGEN

X500

1  COMMON

3  CLOSES TO START

5  OPENS TO START

1  +24V

2  GND

External supply

(24V/0.5A) for Ekip

modules.

G

~

possible to the connectors, see the con-
duit area in picture below. While installing 
the units keep adequate space in the 
sides & rear of the unit for ease of access-
ing the power cables. Be careful not to 
stand on any of the components while ac-
cessing the power cables.

7.2.6  Cable Entry from Bottom /  
Adapter Bay
Adapter bay is an accessory that is used 
when the power connections are coming 
from the bottom. In the adapter bay, all 
the panels are removable. It is installed on 
backside of the Bypass-Isolation Transfer 
Switch cabinet. Conduit entry areas are 
on bottom but also on top.

Summary of Contents for Zenith ZBTS T Series

















































































































Reviews:

No comments