ABB Zenith ZBTS T Series Installation And Operating Instruction Download Page 87 | Manualshive

Page: 87 / 112

ABB Zenith ZBTS T Series Installation And Operating Instruction Download Page 87

2

87

3 4ZBT S _ 3 0 -1 2 0 0A rev. A / 1 S CC 3 0 3 0 4 3 M 0 2 01

3

1

2

—
Fig. 9.4 Trick to release the racking in/out push
button by pressing the lever behind the label (2)

NOTE!

The rack in / out mechanism works

only when the switch is in the OFF posi-
tion and the other switch is in the I / II
position.

4

Finally, reinstall X22 or X12 in the
PCBA to allow normal operation to
continue.

9.2.3 Release the Racking in/out Push
Button
The in/out mechanism of the rack is elec-
trically and mechanically locked. The rack-
ing in/out push button only works if the
switch is in the OFF position and the
other switch is connected to Source 1 or
Source 2.

If you accidentally press the racking in/
out push button (1), but there is no need
to move the switch to the Test or Isolated
location, there is one special trick: The
racking in/out push button can be re-
leased by pressing the lever behind the la-
bel (2). Otherwise, rotate the switch to
the following possible locations, for ex-
ample from the Connected location to the
Test location.

«
...
85
86
87
88
89
...
»

Summary of Contents for Zenith ZBTS T Series

















































































































Reviews:

No comments