manualshive.com logo in svg

ABB Zenith ZBTS T Series, Installation And Operating Instruction, Page: 96 / 112

Share
Download
ABB Zenith ZBTS T Series Installation And Operating Instruction Download Page 96

2

96

Zenith ZBTS T-series 100-1200A, I N S TA LL ATI O N  A N D  O PER ATI N G  I N S TR U C TI O N

3

—

 

9.5  Heater

Heater is used for prevention of conden-
sation, corrosion and leakage currents in 
Bypass-Isolation Automatic Transfer 
Switch cabinet.

Heater and thermostat package are avail-
able as accessory. When ordered, it is in-
stalled in working order at the factory. 

The thermostat is set to 10 °C (50 °F).

Operation: When temperature in cabinet 
drops below thermostat setpoint, heater 

— 
Fig. 9.13  Power supply for heater is taken from  terminals 
X400:1 (LOAD L2) and X400:2 (LOAD L3) on the back side  
of the Control Plate.  

is turned "ON". When temperature is 
above set point, heater turns "OFF".

Thermostat is factory set at 10°C (50°F) 

unless otherwise specified.

All the specified Heater documents are 
delivered with the cabinet. See drawing 
70R-2010.

X400:1 (LOAD L2)
X400:2 ( LOAD L3)

Fig. 9.14  Place of the heater thermostat package on 
the front side of the Control Plate and heater strips 
behind the Control Plate in top of the compartment

1

2

Summary of Contents for Zenith ZBTS T Series

















































































































Reviews:

No comments