manualshive.com logo in svg

ABB Zenith ZBTS T Series, Installation And Operating Instruction, Page: 74 / 112

Share
Download
ABB Zenith ZBTS T Series Installation And Operating Instruction Download Page 74

2

74

Zenith ZBTS T-series 100-1200A, I N S TA LL ATI O N  A N D  O PER ATI N G  I N S TR U C TI O N

— 

7.2  Installation

7.2.1  Power Connections with Screw 
Type Terminals (as standard) 
ABB Zenith Bypass-isolation automatic 
transfer switches are supplied with UL 
listed solderless screw-type terminals as 
standard for the Source 1, Source 2 and 
Load power connections. 

Connect the Source 1, Source 2 and Load 
conductors to the clearly marked termi-
nals on the busbars, see Fig. 7.4:

1 

Source 1 Connectors

2 

Source 2 Connectors

3 

Load Connectors

Remove surface oxides from cables by 
cleaning with a wire brush. Verify that all 
connections are correct places before 
tightening the terminals. All connections 
must be tightened to the proper torque 
values as shown in Table 7.1.

 

Warning

 

Torquing srew-type terminal or compression 
lugs with the improper tool and/or to a torque 
value exceeding the defined parameters may 
result in damage to the switch

.

 

Danger

  

Hazardous voltage may be present. Only an au-

thorised electrician may perform the electri-

cal installation and maintenance of OX_ auto-

matic transfer switches. Do not attempt any 

installation or maintenance actions when By-

pass-Isolation automatic transfer switch is 

connected to the electrical mains. Before 

starting work, make sure that the switch is 

de-energised.

 

Warning

 

The cable lug must be pushed into the oval 

hole of the terminal as close as possible to the 

switch pole.

ZBTS T-series Al/Cu UL Listed Solderless Screw-Type Terminals for External Power 
Connections

Model Amperage Cables 

per 

phase & 

neutral

Lug Type  Cables 

per  

pole

Range of wire sizes

Cables - 

Tightening 

Torque*, 

lb-in (Nm)

ZBTS

100-200

1

OZXA-25 

1

6 AWG - 300 kcmil

(14 - 152 mm

2

)

275 / 31.1 

260-400

1 / 2 OZXA-412L 

1 / 2 1x 4 AWG - 600 kcmil/ 

 

2x 1/0 - 250 kcmil

(1x 25 - 304 mm

2

/ 

2x 55 - 127 mm

2

)

500 / 56.5 

600

2 OZXA-800S 

2

2 AWG - 600 kcmil

(34 - 304 mm

2

)

500/56.5 

800-1200

4 OZXA-1200 

4

2 AWG - 600 kcmil

(34 - 304 mm

2

)

500/56.5 

* Do not exceed this value - may cause damage to switch, voiding warranty

— 
Table 7.1  Tightening torque and wire size for screw-type terminals, see Fig. 7.5

Summary of Contents for Zenith ZBTS T Series

















































































































Reviews:

No comments