manualshive.com logo in svg

ABB Zenith ZBTS T Series, Installation And Operating Instruction, Page: 92 / 112

Share
Download
ABB Zenith ZBTS T Series Installation And Operating Instruction Download Page 92

2

92

Zenith ZBTS T-series 100-1200A, I N S TA LL ATI O N  A N D  O PER ATI N G  I N S TR U C TI O N

3

Position

Pin

Description

H

I S01

Signalling LED of the input I S01 physical status, green.The 

possible states are:  
• Off: input floating.  

• On, fixed: short-circuit between pins HS01 and HS02

I S02

Signalling LED of the input I S02 physical status, green.The 

possible states are: 
• Off: input floating.  

• On, fixed: short-circuit between pins HS03 and HS04.

I S03

Signalling LED of the input I S03 physical status, green.The 

possible states are:  
• Off: input floating.  

• On, fixed: short-circuit between pins HS05 and HS06.

I S04

Signalling LED of the input I S04 physical status, green.The 

possible states are:  
• Off: input floating.  

• On, fixed: short-circuit between pins HS07 and HS08.

I S05

Signalling LED of the input I S05 physical status, green.The 

possible states are:  
• Off: input floating.  

• On, fixed: short-circuit between pins HS09 and HS10.

I S06

Signalling LED of the input I S06 physical status, green.The 

possible states are:  
• Off: input floating.  

• On, fixed: short-circuit between pins HS11 and HS12.

I

I S07

Signalling LED of the input I S07 physical status, green.The 

possible states are:  
• Off: input floating.  

• On, fixed: short-circuit between pins HS13 and HS14.

I S08

Signalling LED of the input I S08 physical status, green.The 

possible states are:  
• Off: input floating.  

• On, fixed: short-circuit between pins HS15 and HS16.

I S09

Signalling LED of the input I S09 physical status, green.The 

possible states are:  
• Off: input floating.  

• On, fixed: short-circuit between pins HS17 and HS18.

I S10

Signalling LED of the input I S10 physical status, green.The 

possible states are:  
• Off: input floating.  

• On, fixed: short-circuit between pins HS19 and HS20.

I S11

Not supported

— 
Table 9.3  Input signals

H

I

Summary of Contents for Zenith ZBTS T Series

















































































































Reviews:

No comments