ABB RELION 650 SERIES Engineering Manual Download Page 9

Page: 9 / 110

Section 1

Introduction

1.1

This manual

GUID-AB423A30-13C2-46AF-B7FE-A73BB425EB5F v14

The engineering manual contains instructions on how to engineer the IEDs using the various

tools available within the PCM600 software. The manual provides instructions on how to set

up a PCM600 project and insert IEDs to the project structure. The manual also recommends a

sequence for the engineering of protection and control functions, LHMI functions as well as

communication engineering for IEC 60870-5-103, IEC 61850 and DNP 3.0.

1.2

Intended audience

GUID-C9B8127F-5748-4BEA-9E4F-CC762FE28A3A v9

This manual addresses system and project engineers involved in the engineering process of a

project, and installation and commissioning personnel, who use technical data during

engineering, installation and commissioning, and in normal service.

The system engineer must have a thorough knowledge of protection and/or control systems,

protection and/or control equipment, protection and/or control functions and the configured

functional logics in the IEDs. The installation and commissioning personnel must have a basic

knowledge of handling electronic equipment.

1MRK 511 284-UEN B

Section 1

Introduction

650 series

Engineering manual

Summary of Contents for RELION 650 SERIES













































































































Search results

Summary of Contents for RELION 650 SERIES

Reviews:

ABB RELION 650 SERIES, Engineering Manual, Page: 9 / 110

Search results

Summary of Contents for RELION 650 SERIES

Reviews: