ABB RELION 650 SERIES Engineering Manual Download Page 57

Page: 57 / 110

IEC08000173_2_en.vsd

BIO

TRM

FBs

GOOSE Inputs

GOOSE FBs for

binary and analog

data, interlocking

communication

and voltage control

IEC 61850

SMAI

FBs

IEC08000173 V2 EN-US

Figure 40: SMT: Operation principles

A binary input channel can be connected to one or several function block inputs, see

Figure 41

If a binary input channel is connected to several different function blocks in ACT, the

connection will appear as glue logic in SMT.

A binary output channel can only be activated from one function block output. If it should be

activated from more than one function block output, glue logic has to be used. Glue logic

means inserting a logical gate (OR and AND blocks) between the function blocks and the

binary output channel. This can be engineered in SMT.

Connections made in SMT are automatically shown in ACT. Connections made

in ACT are automatically shown in SMT.

It is possible to group and collapse hardware channels in SMT to get a better

overview.

1MRK 511 284-UEN B

Section 5

Protection and control engineering

650 series

Engineering manual

Summary of Contents for RELION 650 SERIES













































































































Search results

Summary of Contents for RELION 650 SERIES

Reviews:

ABB RELION 650 SERIES, Engineering Manual, Page: 57 / 110

Search results

Summary of Contents for RELION 650 SERIES

Reviews: