ABB IRB 930 Product Manual Download Page 74 | Manualshive

Page: 74 / 606

background image

Connector kits, outer arm

The table describes the CP/CS and Ethernet (if any) connector kits for the outer
arm.

Art. no.

Description

Position

3HAC066098-001

M12 CPCS Male straight connect-
or kits

CP/CS

Connector kits

3HAC066099-001

M12 CPCS Male angled connector
kits

3HAC067413-001

M12 Ethernet Cat5e Male straight
connector kits

Ethernet

3HAC067414-001

M12 Ethernet Cat5e Male angled
connector kits

Protection covers

Protection covers for water and dust proofing

Protection covers are delivered together with the robot and must be well fitted to
the connectors in any application requiring water and dust proofing.

Always remember to refit the protection covers after removing them.

Note

If the protection covers are not refitted back with the connectors exposed, the
protection class will be lost.

D

C

C

B

A

xx2300000176

Protection covers for air hose connector on the base

A

Protection covers for air hose connector on the process hub

B

Protection covers for C2/SMB connector on the base and C1/C2 connector on
the process hub

C

Continues on next page

74

Product manual - IRB 930

3HAC086009-001 Revision: A

© Copyright 2023 ABB. All rights reserved.

3 Installation and commissioning

3.5.2 Customer connections

Continued

«
...
72
73
74
75
76
...
»

Summary of Contents for IRB 930































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IRB 930

Brand: Parallax Pages: 4

Robotarm SVI-2000

Brand: QuickShot Pages: 6

Brand: Arduino Pages: 39

Education 79100

Brand: K'Nex Pages: 58

Brand: Datavideo Pages: 40

Brand: OCCO Pages: 62

Learn 'N' Fun Robot

Brand: Radio Shack Pages: 2

Brand: 4M Pages: 2

Brand: Hiwin Pages: 5

Brand: WowWee Pages: 11

Brand: WowWee Pages: 12

Brand: SMARS Pages: 8

Brand: Kosmos Pages: 2

Brand: Kosmos Pages: 54

Brand: Husarion Pages: 13

Brand: SMC Networks Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands