ABB IRB 930 Product Manual Download Page 35

Page: 35 / 606

1.7 Safety during troubleshooting

General

When troubleshooting requires work with power switched on, special considerations
must be taken:

•

Safety circuits might be muted or disconnected.

•

Electrical parts must be considered as

live

•

The manipulator can move unexpectedly at any time.

DANGER

Troubleshooting on the controller while powered on must be performed by
personnel trained by ABB or by ABB field engineers.

A risk assessment must be done to address both robot and robot system specific
hazards.

WARNING

Hazards due to the use of brake release devices and/or gravity beneath the
manipulator shall be considered.

A robot may perform unexpected limited movement.

WARNING

Manipulator movements can cause serious injuries on users and may damage
equipment.

Related information

See also the safety information related to installation, operation, maintenance, and
repair.

Product manual - IRB 930

3HAC086009-001 Revision: A

1 Safety

1.7 Safety during troubleshooting

Summary of Contents for IRB 930































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 930

Reviews:

Related manuals for IRB 930

Brands by name

Popular brands

ABB IRB 930, Product Manual

Search results

Summary of Contents for IRB 930

Reviews:

Related manuals for IRB 930

Brands by name

Popular brands