ABB IRB 930 Product Manual Download Page 526 | Manualshive

Page: 526 / 606

background image

Removing the axis-2 gear unit sub-assembly

Use these procedures to remove the axis-2 gear unit sub-assembly.

Preparations before removing the axis-2 gear unit sub-assembly

Note

Action

Decide which calibration routine to use, and take
actions accordingly prior to beginning the repair
procedure.

1

If there is no enough space for the maintenance
work, remove the robot from the wall and place it
on the maintenance bracket.

CAUTION

Do not lay down the robot during the transporta-
tion, always keep it straight.
If the robot lay down in any situation, the grease
may come out from gearbox.

2

xx2300000486

Jog all axes to zero position.

3

DANGER

Turn off all:

•

electric power supply

•

hydraulic pressure supply

•

air pressure supply

to the robot, before entering the safeguarded
space.

4

Draining oil of axis-2 gearbox

Note

Action

WARNING

Handling gearbox oil involves several
safety risks, see

Gearbox lubricants (oil or

grease) on page 30

1

Continues on next page

526

Product manual - IRB 930

3HAC086009-001 Revision: A

© Copyright 2023 ABB. All rights reserved.

5 Repair

5.8.2 Replacing the axis-2 gear unit sub-assembly

Continued

«
...
524
525
526
527
528
...
»

Summary of Contents for IRB 930































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IRB 930

Faber HM-G Series

Brand: Denso Pages: 174

Brand: Nexus Automation Pages: 128

Keyestudio 4WD Mecanum Robot Car

Brand: Eckstein komponente Pages: 369

Mitu Bunny JMJQR01IQI

Brand: Xiaomi Pages: 5

Brand: Gear2Play Pages: 25

Brand: TTS Pages: 3

Brand: TTS Pages: 16

Brand: SMART Pages: 38

Brand: SMART Pages: 40

Brand: SoftBank Pages: 24

ProtoSnap MiniBot

Brand: sparkfun Pages: 16

Brand: sparkfun Pages: 39

Brand: Staubli Pages: 42

E-SwitchON-SKUR454

Brand: Robosoft Pages: 11

Brand: Robot Pages: 15

Optimus Prime Trailer Kit Elite

Brand: Robosen Pages: 19

OPTIMUS PRIME ELITE

Brand: Robosen Pages: 21

Interstellar Scout

Brand: Robosen Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands