ABB IRB 930 Product Manual Download Page 473

Page: 473 / 606

Note

Action

Timing belt, A4:

Refit the timing belt to the pulley on the ball screw
and the motor. Ensure that the belt runs correctly
in the grooves.

3HAC081706-001

xx2300000588

Screws: Hex socket head cap
flange screw 3HAB3412-520 M5x16
12.9 Lafre 2C2B/FC6.9+PrO-
COat111 (6 pcs)

Refit the screws and washers without fully
tightened.

xx2300000558

Used belt: 312-333 Hz

Use a sonic tension meter to measure the timing
belt tension.

New belt:88.4-92.7 Hz

If the timing belt tension does not meet the require-
ment, readjust the motor with the adjusting screw.

Tightening torque: 6 Nm ±10%

Tighten the motor screws when the timing belt
meets the requirement.

Refitting the cable ferrule and bracket in the outer arm

Note

Action

Lay the internal harness in a natural state without
distortion.

Continues on next page

Product manual - IRB 930

473

3HAC086009-001 Revision: A

5 Repair

5.7.4 Replacing the axis-4 motor sub-assembly

Continued

Summary of Contents for IRB 930































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 930

Reviews:

Related manuals for IRB 930

Brands by name

Popular brands

ABB IRB 930, Product Manual

Search results

Summary of Contents for IRB 930

Reviews:

Related manuals for IRB 930

Brands by name

Popular brands