ABB DSQC1016 Manual Download Page 53

Page: 53 / 156

3.7 Verifying the installation of the service box

Overview

This section describes about LEDs to verify that the Service Box is active. It also
provides an instruction to make a notification to get traceability.

Note

The robot controller must be in operating mode before the LEDs can be checked.

Note

In case of any problem during installation, report the case in RobDesk.

Note

The SD card slot and USB slot of the service box are not used. Keep the stickers
blocking them, otherwise warranty will not be applicable.

LEDs

en1600001572

LEDs in the front of the Service Box indicate if the box is functioning. The LEDs
should be lit as follows:

Indication

LED

Indicates that the reset button is pressed

BI1

Continues on next page

Product manual - Connected Services

3HAC060439-001 Revision: E

3 Installation of Service Box in Robot Controllers

3.7 Verifying the installation of the service box

Summary of Contents for DSQC1016




























































































































































Search results

Summary of Contents for DSQC1016

Reviews:

Related manuals for DSQC1016

Brands by name

Popular brands

ABB DSQC1016, Manual

Search results

Summary of Contents for DSQC1016

Reviews:

Related manuals for DSQC1016

Brands by name

Popular brands