ABB 2CSYK1201C Product Manual Download

Page: 8 / 76

8 Technical features

| MYLOS

Building Automation

MYLOS

Building Automation

Technical features

2.4

Assembly and installation

The thermostat with display is a flash-mounted device with an integrated bus coupler. The device operates without
additional supply voltage.

Selection of a suitable installation location for the controller and suitable parameter settings are essential for good
temperature detection.

- The ambient temperature controller should be

installed approximately 150 cm above the floor and
50 cm from the door frame.

- The ambient temperature controller should be

installed on a wall opposite the radiator.

- The radiator and the ambient temperature controller

must not be separated by corners in the room.

- An ambient temperature controller should not be

installed near a radiator or behind curtains.

- It should also not be installed on an exterior wall

because low outside temperatures will influence
the temperature detection.

Summary of Contents for 2CSYK1201C













































































Search results

Summary of Contents for 2CSYK1201C

Reviews:

Related manuals for 2CSYK1201C

Brands by name

Popular brands

ABB 2CSYK1201C, Product Manual

Search results

Summary of Contents for 2CSYK1201C

Reviews:

Related manuals for 2CSYK1201C

Brands by name

Popular brands