background image

1 Safety

1.1 Safety signals in the manual

Introduction to safety signals

This section specifies all safety signals used in the user manuals. Each signal
consists of:

A caption specifying the danger level (DANGER, WARNING, or CAUTION)
and the type of danger.

A brief description of what will happen if the the danger is not eliminated.

Instruction about how to eliminate danger to simplify doing the work.

Danger levels

The table below defines the captions specifying the danger levels used throughout
this manual.

Significance

Designation

Symbol

Warns that an accident

will

occur if the instructions

are not followed, resulting in a serious or fatal injury
and/or severe damage to the product. It applies to
warnings that apply to danger with, for example,
contact with high voltage electrical units, explosion
or fire risk, risk of poisonous gases, risk of crushing,
impact, fall from height, and so on.

DANGER

Warns that an accident

may

occur if the instructions

are not followed that can lead to serious injury, pos-
sibly fatal, and/or great damage to the product. It
applies to warnings that apply to danger with, for
example, contact with high voltage electrical units,
explosion or fire risk, risk of poisonous gases, risk
of crushing, impact, fall from height, etc.

WARNING

Warns for electrical hazards which could result in
severe personal injury or death.

ELECTRICAL
SHOCK

Warns that an accident may occur if the instructions
are not followed that can result in injury and/or
damage to the product. It also applies to warnings
of risks that include burns, eye injury, skin injury,
hearing damage, crushing or slipping, tripping, im-
pact, fall from height, etc. Furthermore, it applies to
warnings that include function requirements when
fitting and removing equipment where there is a risk
of damaging the product or causing a breakdown.

CAUTION

Warns for electrostatic hazards which could result
in severe damage to the product.

ELECTROSTATIC
DISCHARGE (ESD)

Continues on next page

Application manual - BullsEye

11

3HAC050989-001 Revision: C

© Copyright 2004-2018 ABB. All rights reserved.

1 Safety

1.1 Safety signals in the manual

Summary of Contents for 0503060880



























































































Reviews: