manualshive.com logo in svg

Aastra AastraLink Pro 160, Administrator'S Manual

Share
Download
Aastra AastraLink Pro 160 Administrator'S Manual Download Page 299

Reinstalling System Software Using Recovery Mode

41-001190-02 Rev. 01, Rel. 1.2 

7-11

Troubleshooting Solutions

Reinstalling System Software Using
Recovery Mode

The AastraLink Pro 160 contains an automatic fail-back mode in its onboard 
firmware that allows the system to be recovered if it encounters a problem when 
booting from the CompactFlash root file system.

The AastraLink Pro 160 enters automatic “recovery mode” after a failed boot. If 
necessary, it is also possible for you to initiate recovery mode, by booting the 
system with the CompactFlash card removed (see 

“Manual Recovery Mode”

 on 

page 7-13

 for instructions). 

When the AastraLink Pro 160 is in recovery mode, you can use your web browser 
to access the Recovery Mode UI, which allows you to: 

•

Reprogram the CompactFlash card back to the default “greenfield” state, as if 
it were just received new from the factory.

•

Reprogram the Onboard flash (firmware), using a new firmware image.

•

Restore a previous .

avf 

backup file onto the ComapctFlash.

Caution: 

Reprogram the Onboard flash under the direction of Aastra support 

personnel only. Incorrect usage can make the AastraLink Pro 160 
unbootable, requiring the device to be returned to the factory for repair. 

Summary of Contents for AastraLink Pro 160









































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands