3D Systems Viper Pro SLA User Manual Download

Page: 91 / 121

www.3dsystems.com

t r o u b l e s h o o t i n g

user

’

s manual

Troubleshooting

Power Outages

Viper Pro SLA System Shutdown

Error Symptoms and Other Problems

If you are present when a power outage occurs, or if you discover that the main power is off,
complete the following steps:

1. Switch the power OFF at the Viper Pro SLA system’s electronic cabinet so that it does not

automatically start when the power is restored; doing so prevents damage from power flickers
and surges.

2. When the power is restored and stable, switch the Viper Pro SLA system power ON at the

cabinet.

If you do not plan on operating the Viper Pro SLA system on a regular basis and want to shut it
down for an extended period of time, shut down Windows and turn off the main disconnect. See
“

Electrical Cabinet: Closed Door

”.

Note: It takes a substantial amount of time for the Viper Pro SLA system to warm up
after a full shutdown/power off. See

Resin Delivery Module Temperature Control

“

Error Symptoms

” contain problems that can occur with your Viper Pro SLA system. Please consult

the table if you have any problems.

70696 Revision 1C 27-Aug-08

Summary of Contents for Viper Pro SLA


























































































































Search results

Summary of Contents for Viper Pro SLA

Reviews:

Related manuals for Viper Pro SLA

Brands by name

Popular brands

3D Systems Viper Pro SLA, User Manual

Search results

Summary of Contents for Viper Pro SLA

Reviews:

Related manuals for Viper Pro SLA

Brands by name

Popular brands