3D Systems Viper Pro SLA User Manual Download Page 110

Page: 110 / 121

110

Line

A line of cured plastic generated by overlapping bullets. See also vector.

Linewidth

The horizontal width of a laser cured resin line.

Monomer

A low molecular weight chemical species, which is a building block of polymers.

MSDS

Material Safety Data Sheet. Federal government mandated information about the chemical makeup
of any chemical substance, such as resin. Usually includes identification of toxic substances and
safe handling guidelines.

NIOSH

National Institute for Occupational Safety and Health.

Photoinitiator

A chemical in photopolymers that reacts with photons and catalyzes the polymerization process.

Photopolymer

A chemical substance composed of photoinitiators and monomers that polymerizes when exposed
to light energy.

70696 Revision 1C 27-Aug-08

Summary of Contents for Viper Pro SLA


























































































































Search results

Summary of Contents for Viper Pro SLA

Reviews:

Related manuals for Viper Pro SLA

Brands by name

Popular brands

3D Systems Viper Pro SLA, User Manual

Search results

Summary of Contents for Viper Pro SLA

Reviews:

Related manuals for Viper Pro SLA

Brands by name

Popular brands