3D Systems Viper Pro SLA User Manual Download

Page: 73 / 121

www.3dsystems.com

b u i l d w i n d o w

user

’

s manual

Position:

Shows the position of the build status depending on original CAD Z coordinate. The

units, inches or millimeters, will be consistent with the units used in the build file.

Percent:

With 0% as the start and 100% as the end, shows the percentage completed of the

current build.

Duration:

With 0:00 as the start and the projected time of completion as the end, shows the time

that has elapsed at the current build.

Time:

In real time, this clock shows the time that the build started, the current time, and the

projected time at the end of the build.

Note: The format of the values in the right hand column will change depending on the
dropdown selected.

70696 Revision 1C 27-Aug-08

Summary of Contents for Viper Pro SLA


























































































































Search results

Summary of Contents for Viper Pro SLA

Reviews:

Related manuals for Viper Pro SLA

Brands by name

Popular brands

3D Systems Viper Pro SLA, User Manual

Search results

Summary of Contents for Viper Pro SLA

Reviews:

Related manuals for Viper Pro SLA

Brands by name

Popular brands