3D Systems Viper Pro SLA User Manual Download Page 29

Page: 29 / 121

Refill Container 1 and 2:

These removable containers store new resin, which is added to the

RDM as needed, prior to the start of a build.

Blade Rest:

The blade rest area is used to stow the removable recoater blade when changing

RDMs.

Leveling Container:

The system requires precise control of the resin height. This container acts

as a storage reservoir.

Note: Under normal operations, this container is not to be removed.

Valve Assembly:

These valves control the resin flow from the refill containers and recirculate

resin.

Leveling Pump:

The leveling pump controls the resin height in the RDM by moving resin to or

from the leveling container.

RDM Heater Power Switch:

This switch enables warm up of the RDM, whether in the system or

offline.

I/O Connector:

This connector is the interface for all communication and motion control

between the RDM and the Viper Pro SLA system.

Gross Fill/Circulation Pump:

This pump transfers resin from the refill containers into the RDM,

and recirculates resin already in the RDM.

70696 Revision 1C 27-Aug-08

Summary of Contents for Viper Pro SLA


























































































































Search results

Summary of Contents for Viper Pro SLA

Reviews:

Related manuals for Viper Pro SLA

Brands by name

Popular brands

3D Systems Viper Pro SLA, User Manual

Search results

Summary of Contents for Viper Pro SLA

Reviews:

Related manuals for Viper Pro SLA

Brands by name

Popular brands