3D Systems Viper Pro SLA User Manual Download Page 85 | Manualshive

Page: 85 / 121

background image

www.3dsystems.com

85

r e c o a t e r s y s t e m

RDM Removal

The RDM is made of stainless steel and has casters for moving and maneuvering it while
installing or removing it from the frame. There are also handles on the RDM that help the user to
transport and maneuver it into and out of the Viper Pro SLA system.

6. Make sure that the elevator is at its lowest position

before you move

the RDM out of the machine.

7. Make sure that the connecting cables are out of the way of the RDM before you take the RDM

out of the machine.

8. Place the RDM lid into position.
9. Take the RDM out of the machine and close the RDM door.

Recirculation

During periods of non-operation, the RDM can recirculate resin to improve resin uniformity and
life. For more information, see “

1. Open the RDM door.
2. Exit the 3DPrint software (this will ensure the valve position on
the RDM is properly closed for removal).
3. Turn off the switch and disconnect the power cord. (See “

Heater Power Switch

4. Disconnect the cables. There is a black power cord and a gray
cable bundle. Unplug the three pronged black power cord from the
IEC receptacle on the RDM and take the connector out of the keys.
(See “

RDM Umbilical Cord Receptacle

”.)

5. Disconnect the locking pin, located on the outer side of the
machine. (See “

”)

70696 Revision 1C 27-Aug-08

«
...
83
84
85
86
87
...
»

Summary of Contents for Viper Pro SLA


























































































































Reviews:

No comments

Related manuals for Viper Pro SLA

CLP 510N - Color Laser Printer

Brand: Samsung Pages: 270

Bixolon SRP-270

Brand: Samsung Pages: 13

Brand: Oki Pages: 16

Brand: Olivetti Pages: 179

Brand: Olivetti Pages: 36

Brand: Oki Pages: 679

Brand: Oki Pages: 40

Brand: OKIDATA Pages: 308

Brand: OKIDATA Pages: 9

Brand: OKIDATA Pages: 2

Microline 8480 FB

Brand: Oki Pages: 12

3250D - Phaser B/W Laser Printer

Brand: Xerox Pages: 12

Brand: Xerox Pages: 4

Brand: Xerox Pages: 12

Brand: Datamax Pages: 19

Brand: Oki Pages: 2

DRYPRO Model 793

Brand: Konica Minolta Pages: 156

Brand: Roland Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands