3D Systems ProJet 2500 User Manual Download | Manualshive

Page: 44 / 53

background image

3D Systems, Inc.

Waste Bag Maintenance

Behind the Support Material cartridges there is a waste bag receptacle area . In the receptacle a disposable bag and hard liner are

contained. The waste bag and liner will need to be changed periodically. Follow the steps below for changing the waste bag:

Changing Waste Bag

1 . Verify that the printer is OFFLINE .

2 . Ensure printer is warm .

3 . Wearing protective nitrile gloves, open the MDM drawer .

4 . Remove waste bag .

NOTE: If the waste bag is stuck to the liner when you attempt to
remove it, replace the entire liner and bag to prevent the bag
from tearing and causing material to leak into the receptacle .
Waste bags can be ordered using part number 311215-00 .
With each order you will receive 30 bags and 1 liner .

5 . Dispose of bag according to local regulations .

6 . Inspect waste bin for any remaining waste . If necessary, wipe out any

waste that exists with a lint free cloth and isopropyl alcohol .

7 . Replace bag and close MDM .

8 . Return printer ONLINE and it is ready to use .

39

«
...
42
43
44
45
46
...
»

Summary of Contents for ProJet 2500






















































Reviews:

No comments

Related manuals for ProJet 2500

Brand: Unisys Pages: 255

Brand: Xerox Pages: 199

Brand: Oki Pages: 100

Brand: Oki Pages: 2

Brand: Xerox Pages: 4

Brand: Oki Pages: 38

Brand: Oki Pages: 38

Brand: Oki Pages: 36

Brand: Oki Pages: 36

Brand: Eazao Pages: 50

Power Defense PD3

Brand: Eaton Pages: 4

7760DN - Phaser Color Laser Printer

Brand: Xerox Pages: 158

Brand: Xerox Pages: 2

Brand: Xerox Pages: 16

Brand: Citizen Pages: 133

Brand: iFactory3D Pages: 14

Brand: Xiamen Hanin Electronic Technology Pages: 27

Brand: LaserLine Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands