3D Systems ProJet 2500 User Manual Download | Manualshive

Page: 36 / 53

background image

3D Systems, Inc.

PRINT PLATFORM REMOVAL AND INSTALLATION

1 . Ensure the printer is turned on and the Printer State is in

Idle

or

Standby

mode .

NOTE: This is the normal state you should find the

printer in when you open the door .

NOTE: Make sure you are wearing nitrile gloves
before performing this procedure . Always protect
yourself from possible exposure to materials .

2 . Select the

Access Platform

button on the printer

touchscreen .

NOTE: The Access Platform will not be available
to select if the printer is not ready for the user to
access the print platform .

3 . The printer will move the plate into place in order to allow

access to the build platform . When prompted, open the door
to access the print platform .

4 . Wearing nitrile gloves, lift platform off of plate .

31

«
...
34
35
36
37
38
...
»

Summary of Contents for ProJet 2500






















































Reviews:

No comments

Related manuals for ProJet 2500

WorkCentre 7300 Series

Brand: Xerox Pages: 40

6200DX - Phaser Color Laser Printer

Brand: Xerox Pages: 42

5550B - Phaser B/W Laser Printer

Brand: Xerox Pages: 4

Brand: Xerox Pages: 2

Brand: Xerox Pages: 192

Brand: Xerox Pages: 10

Brand: Xerox Pages: 15

Brand: Printek Pages: 34

7760DX - Phaser Color Laser Printer

Brand: Xerox Pages: 4

Brand: RHINO Pages: 21

Brand: Ocom Pages: 23

Brand: Z Corporation Pages: 70

Brand: Loadrite Pages: 16

Brand: Dascom Pages: 2

Brand: Polaroid Pages: 8

Brand: Polaroid Pages: 52

Brand: IGA Pages: 42

Brand: Triumph Adler Pages: 224

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands