manualshive.com logo in svg

3D Systems ProJet 2500, User Manual, Page: 28 / 53

Share
Download
3D Systems ProJet 2500 User Manual Download Page 28

3D Systems, Inc.

7

   CLEANING AND MAINTENANCE PROCEDURES

INSPECT PLANARIZER PROCEDURE

The planarizer requires no adjustments once it is installed on the printer .The planarizer does require cleaning as part of a preventive 
maintenance cycle .

Cleaning the Planarizer Blade

1 .  Move print engine to the 

Ready

 state by selecting 

Inspect 

Planarizer

 under 

Tools > Diagnostics

 in the UI . This will 

place the printer over build plate area and will tilt the blade .

2 .  Lift the cover to expose the planarizer blade .

3 .  While wearing nitrile gloves, wipe excess material from 

the blade using a lint-free cloth, if necessary apply some 
isopropyl alcohol to the cloth before wiping .

CAUTION: Blade is sharp, be careful not to cut 
yourself when wiping blade .

NOTE: If buildup cannot be cleaned off, or if there are 
signs of damage to the blade, it may be necessary 
to replace it . See 

Replacing Planarizer Blade

 for 

instructions .

23

Summary of Contents for ProJet 2500






















































Reviews:

No comments