manualshive.com logo in svg

3D Systems ProJet 2500, User Manual, Page: 34 / 53

Share
Download
3D Systems ProJet 2500 User Manual Download Page 34

3D Systems, Inc.

SHRINK COMPENSATION FOR PROJET VISIJET

®

 MATERIALS

Material shrinkage occurs in thermosets as they transition from liquid state to solid state during the curing process .

The ProJet Accelerator Client Software has features that allow the user to compensate for the natural shrinkage of the material in order 

to fine tune the accuracy of a part.

These shrink compensation values serve as general guidelines to setting shrink compensation . Part building and cleaning in a 
controlled process will best determine the optimal shrink compensation values for a particular geometry .

Material

X Value

Y Value

Z Value

VisiJet® M2 RWT (Rigid White)

1 .01%

1 .01%

0 .00%

VisiJet® M2 RCL (Rigid Clear)

1 .01%

1 .01%

0 .00%

VisiJet® M2 RBK (Rigid Black)

0 .55%

0 .25%

0 .00%

VisiJet® M2 EBK (Elastomeric Black)

VisiJet® M2 ENT (Elastomeric Natural)

Enter Standard Shrink Compensation Values for the material .

1 .  Open 

ProJet Accelerator

 Client software and select the desired 3D printer system .

2 .  Select the part to build .

3 .  Select the 

Options

 Button

4 .  Within the 

Options

 panel, enter shrink compensation values for X, Y, and Z if necessary (compensation is rarely necessary, see 

chart on previous page for values) .

WAITING ON SHRINK COMPENSATION 

INFORMATION FROM WILSONVILLE .

29

Summary of Contents for ProJet 2500






















































Reviews:

No comments