Ziton ZP2-AF2-P Скачать руководство пользователя страница 76

Страница: 76 / 176

Chapter 3: Configuration and commissioning

ZP2-A Series Installation Manual

Regional options

Select Regional options to set the regional operating mode. Available options are

shown in the table below.

Table 26: Regional operating modes
Operating mode

Region

EN 54-2 (default)

European Union

EN 54-2 Evacuation

European Union (Spain)

NBN S 21-100 [1]

European Union (Belgium)

NEN 2535/2575 [2]

European Union (Holland)

VdS 2540 [1]

European Union (Germany)

British Standard [3]

United Kingdom

[1] See the corresponding marketplace manuals for additional installation and operation

instructions for these regional operating modes.

[2] Implements NEN 2535 for fire and repeater panels and NEN 2575 for evacuation panels.

[3] Defaults the panel to UK English.

To change the control panel operation mode:

1.  Select Panel setup from the Main menu.
2.  Select Regional options.
3.  Select the operating mode.
4.  Press F4 (Enter), and then press F1 (Back).
5.  Press F1 (Save), F3 (Apply), F4 (Discard), or F2 (Exit)

Remember to apply saved settings from the Main menu.

Содержание ZP2-AF2-P

















































































































































































Результаты поиска

Содержание ZP2-AF2-P

Отзывы:

Похожие инструкции для ZP2-AF2-P

Бренды по названию

Популярные бренды

Ziton ZP2-AF2-P, Руководство по установке

Результаты поиска

Содержание ZP2-AF2-P

Отзывы:

Похожие инструкции для ZP2-AF2-P

Бренды по названию

Популярные бренды