ZIEHL-ABEGG ZETADYN 1DV Series, Описание системы

Страница: 43 / 69

38 Operation and settings
4.3.11 The menu "ZA-INTERN"
Contents: In menu "ZA-Intern", controller internal settings are stored. Changes are only to be made on
consultation with the manufacturer.
ZA-INTERN
**********************
----------------------------
Error suppression:
MASK1 0
MASK2 0
MASK3 0
----------------------------
Control functions:
T_GUE 2.0s
V_UE 50 %
T_AUS 7.0s
----------------------------
Start-Opti.:
ANF_D EIN
M0_T1 50 ms
V_DM 1.0%
VB_T1 100 ms
S0<= 2
----------------------------
Stop-Opti.:
A10 0.5 m/s2
S_HALT 5.0cm
R_N1 50%
HALT t-Halt
T_NB 250ms
---------------------------- ----------------------------
Info:
STATUS
> Service number
SE_NR .....
ZA ......
> ZA manafacture
ZETAMON:
MS_1 0
>
MS_2 0
RS232 4800
>
----------------------------
Controller:
K_N1 1400
T_N2 110ms
T_N1 110ms
K_N2 1400
BR_F 70%
BR_OF 18%
P_T1 300 &
> >
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
Figure 4.17 Menu "ZA-Intern"
MASK1 It is possible to attenuate three error messages. To do this. the corresponding error number is
MASK3 to be put in.
T_GUE If no speed transmitter signal appears within the time T_GUE, the control device switches to error and
displays the error message "9 No starting" or "14 Encoder trop out".
V_UE If the actual speed exceeds the value of the rated speed to the nominal speed by more than 50 % or if
it falls below more than 50 %, the control device switches to trouble and displays the error message
"36 N_PROG << N_REAL" resp. "35 N_PROG >> N_REAL".
T_AUS The control device stops the run in case of running without driving command but with triggered
controller release "RF" after the time T_AUS.
ANF_D When the starting attenuation is switched on, the nominal value is kept in a tolerance range V_DM
V_DM until the actual value follows. A smaller value for V_DM causes a smoother start-up.
VB_T1 Determines the return-to-zero period in which the pre-braking torque M_VB returns to zero.
MO_T1 Determines the return-to-zero period in which the starting torque M0 returns to zero.
S0<= Determines the number of speed transmitter pulses attenuated by the rotation direction evaluation at
start-up.
HALT Setting whether the positioning process (V1->0) is to be effected depending on the time or the
distance.
A_10 If HALT = t-Halt: Decelerating value for positioning process.
R_10 If HALT = t-Halt: Rounding of V1 ->0 transfer.
S_HALT If HALT = s-Halt: Absolute positioning distance.
T_NB Determines the time how long the after-braking torque is to be fed after closing the contact "MB".
K_N1/2 For the run with V3, it is possible to adjust the reset time and the amplification of the speed
T_N1/2 regulator separately.
BR_F Influencing the effect of the DC-winding.
BR_OF Crossover range between "Drive" and "Brake".
P_T1 Internal value for low-pass filter.
MS_1 Setting of the measuring value storage 1.
MS_2 Setting of the measuring value storage 2.
RS232 Setting of the baud rate (2400, 4800 and 9600 Baud).
STATUS Internal state of the control device at the moment.
SE_NR Indication of the current password coded. In case of password loss, please inform the manufacturer
of the contents of SE_NR.
ZA Ziehl -Abegg specific identification of the control device software.