manualshive.com logo in svg

ZCS HYDxxxxES Series, Руководство пользователя

Поделиться
Скачать
ZCS HYDxxxxES Series Скачать руководство пользователя страница 43

 

 43 / 45 

ID32 

SwBOCPInstant 

The input current is too high 

Check  whether  the  input  current  is  higher  than 
the  maximum  input  current  of  HYD-ES  inverter, 
then  check  the  input  wiring,  if  both  are  correct, 
please contact technical support. 

ID33 

PvConfigSetWr
ong 

Incorrect input mode 

Check  the 

PV  input  mode

  (parallel  mode/ 

independent mode) setting of HYD-ES inverter. If 
it’s incorrect, change the 

PV input mode

. 

ID48 

ConsistenFault-
fault 

The  GFCI  sampling  value  between 
the  master  DSP  and  slave  DSP  is 
not consistent 

ID48-ID51  are  internal  faults  of  the  HYD-ES 
inverter, switch OFF the HYD-ES inverter, wait for 
5  minutes,  then  switch  ON  the  HYD-ES  inverter. 
Check whether the problem is solved.  

If not, please contact ZCS technical support.

 

ID49 

ConsistentFault
_Vgrid 

The  grid  voltage  sampling  value 
between the master DSP and slave 
DSP is not consistent 

ID50 

ConsistentFault
_Fgrid 

The  grid  frequency  sampling  value 
between the master DSP and slave 
DSP is not consistent 

ID51 

ConsistentFault
_DCI 

The  Dci  sampling  value  between 
the  master  DSP  and  slave  DSP  is 
not consistent 

ID52 

BatCommunica
ton 

Flag 

HYD-ES inverter can’t communicate 
with Lithium battery BMS correctly.  

Make sure the battery you’re using is compatible 
with HYD-ES inverter. 

Make  sure  you’ve  selected  the  correct  battery 
type.  Check  the  communication  cable  between 
battery & HYD-ES inverter. 

It’s recommended to use CAN communication. 

For PYLONTECH US2000 PLUS battery, when using 
RS485  communication,  the  ADD  DIP  switch 
should be all down. 

ID53 

SpiCommLose 

SPI communication is fault 

ID53-ID55  are  internal  faults  of  the  HYD-ES 
inverter, switch OFF the HYD-ES inverter, wait for 
5  minutes,  then  switch  ON  the  HYD-ES  inverter. 
Check whether the problem is solved.  

If not, please contact ZCS technical support. 

ID54 

SciCommLose 

SCI communication is fault 

ID55 

RecoverRelayFa
il 

 relays fault  

ID56 

PvIsoFault 

The insulation resistance is too low 

Check  the  insulation  resistance  between  the  PV 
array and earth(ground),  

ID57 

OverTempFault
_BAT 

The battery temp is too high  

Please make sure HYD-ES inverter is installed in a 
place without direct sunlight. 

Please make sure HYD-ES inverter is installed in a 
cool / well-ventilated place. 

Make sure the inverter is vertically installed & the 

ID58 

OverTempFault
_ 

HeatSink 

The temperature of heat sink is too 
high 

Содержание HYDxxxxES Series














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды