Zapi ACE3 Скачать руководство пользователя

Страница: 65 / 139

AFFZP0BB – ACE3 – User Manual

Page – 65/139

TESTER (Master)

Parameter

Unit of measurement

(resolution)

Description

TEMPERATURE

(A)

Celsius degrees (1 °C)

Temperature measured on the inverter base plate.

This temperature is used for the HIGH TEMPERATURE
alarm.

MOTOR TEMPERAT.

(A)

Celsius degrees (1 °C)

Motor-windings temperature.

Normally the sensor is a PTC Philips KTY84-130. This
temperature is used for the MOTOR OVERTEMP alarm.

A6 TILLER

(T, TM)

OFF/ON

Status of the TILLER/SEAT input (A6).

A11 QI/PB

(T, TM)

OFF/ON

Status of the Pedal-Brake/Quick-Inversion input (A11)

B13 HS

(T, TM)

OFF/ON

Status of the Hard&Soft input (B13).

A4 FW SW

(T, TM, TS)

OFF/ON

Status of the forward input (A4).

A4 ENABLE

(T, TM, TS)

OFF/ON

Status of the driving-demand input (A4).

A5 BW SW

(T, TM)

OFF/ON

Status of the backward input (A5).

B11 AUX3

(T, TM)

OFF/ON

Status of the AUX3 input (B11) that enables EV3

B4 AUX1

(T, TM)

OFF/ON

Status of the AUX3 input (B4) that enables EV1

B5 AUX2

(T, TM)

OFF/ON

Status of the AUX3 input (B5) that enables EV2

A13 SR/HB

(T, TM)

OFF/ON

Status of the Speed-Reduction/Hand-Brake input (A13).

B6 FW-INCH

(TS)

OFF/ON

Status of the forward-inching input (B6).

B13 L-BW-IN

(TS)

OFF/ON

Status of the backward-inching input (B13).

A6 SEAT

(P)

OFF/ON

Status of the TILLER/SEAT input (A6).

Содержание ACE3












































































































































Результаты поиска

Содержание ACE3

Отзывы:

Похожие инструкции для ACE3

Бренды по названию

Популярные бренды

Zapi ACE3, Руководство пользователя

Результаты поиска

Содержание ACE3

Отзывы:

Похожие инструкции для ACE3

Бренды по названию

Популярные бренды